| Results 1 - 16 of 16 | Page 1 of 1 |
| Results per-page: 10 | 20 | 50 | 100 |
Posted on: 10/19/2020
Community Member Credit: iansw So I've been asked to do a write-up on how to make the Z32 MAF setup work with the JWT ECU + 370cc Injectors while Supercharged on the charged side. Symptoms: With the Z32 MAF on the charged side and stock Stillen piping the car idles…
Posted on: 09/22/2020
Community Member Credit: WildmanAL This setup uses the Blemhco Front and Rear Adapter Kit (which is no longer available). You can learn more about it here: https://www.my4dsc.com/blehmco-maxima-big-brake-kits/ As for stopping power, it's a hell of a lot better than stock. It's a lot smoother and you can actually feel the…
Posted on: 09/22/2020
Blehmco Kit: Z32 Calipers 2004 6thgen Maxima Rotors Relocation brackets Conversion Lines Jeff92se Kit: z32 calipers Cobra rotors relocation brackets center rings conversion lines Z32 Direct Rotor Swap: Z32 calipers Z32 rotors (must be milled down) conversion lines. Additional Info: You have to mill down the diameter of the rotor,…
Posted on: 09/20/2020
Community Member Credit: Josh Go Hard Neal BlackPath's Caliper Kit allows the installation of larger 300ZX calipers and 12.75" 350Z rotors (not included) on your Nissan Maxima. The bracket is made for a 240SX but also fits your 4thgen or 5thgen Nissan Maxima. Important Note: You will need the 350z…
Posted on: 09/13/2020
Z32 MAF Part Number: 22680-30P00 Tomei Z32 Airflow Meter Harness Part Number: 194002 The Z32 Mass Air Flow (MAF) sensor is great for turbo or supercharged setups. If you are not boosted then you do not need these. If you are boosted, the Z32 MAF allows you to measure more…
Posted on: 09/07/2020
If you've never changed out your fuel filter on 4thgen Nissan Maxima, you should consider using the Z32 300ZX TT fuel filter. It's a bit larger in size and is known to last longer than your Nissan Maxima regular OEM filter. Please Note: The size of the fuel filter does…
Posted on: 09/06/2020
Credit: Andy Woo (Internet Z Car Club (IZCC)) 1) Loosen the lug nuts on the wheels corresponding to the brake pads you are planning to change. 2) Jack up the car (refer to How To for examples). Make sure you use wheel chocks and do not engage the emergency brakes. 4) Lay…
Posted on: 06/14/2020
Member Credit: Andrew Nicholas Until someone can TRULY engineer perfect Akebono brackets that bolt on to front Altima with zero modding needed, I only recommend this to people who are mechanically inclined, are willing to DIY, and go through some trial and error and use your intuition. Z1 motorsports 300ZX…
Posted on: 05/30/2020
Member Credit: Aackshun Caliper Models: G35 Coupe and Sedan 2005, 2006, 2007 (Coupe only for '07) and Non-Brembo Equipped 350z 2006, 2007 and 2008 models. How to Applies to the Following Vehicles: -J30 (89-94) Maxima -A32 (95-99) Maxima -A33 / A33B (2000-2003) Maxima -A34 (2004-2008) Maxima -L31 (2002-2006) Altima Maybe…
Posted on: 12/25/2018
Member Credit: 95BLKMAX I wanted bigger brakes, but I didnt want to spend a fortune (as much as one would spend, say for a Z32 upgrade, or the 6th gen rotors with Z32 calipers, etc...) for just front brakes. Plus I dont autoX, I just do alot of highway spirited driving;…
Posted on: 10/31/2018
Member Credit: Nperez1986 / Jonthon Rubia If you are looking to upgrade to the Akebono 4-Piston BBK from a Nissan 370z / Infiniti G37 Sport, you now have the option to use 300ZX (Z32) caliper adapter brackets on eBay. The bracket themselves are $70 bucks shipped. In order for this to work,…
Posted on: 05/06/2018
Member Credit: mastercater7 aka Zack I wanted to post on here to share my project as well as do my best to help others. I am a member on maxima.org, but as far as having a boosted VQ35, there are not many people. Thus, needing input or help with problems can…
Posted on: 01/13/2018
Member Credit: Matt Blehm Please note that this post is for reference and documentation purposes ONLY. Matt Blehm no longer offers these products or services. Products were available from 2003 to around 2009. BlehmCo Maxima Big Brake Kits Front Big Brake Kit #1--2004 Maxima Rotors with 300ZX calipers: This kit fits…
Posted on: 12/24/2017
Member Credit: EddyMaxx For your 6thgen's you need either the 30MM Aluminum or 30MM Iron Z32 Calipers for proper fitment. They are 4-Piston calipers. You will also need the brackets for them. You can usually find the calipers on eBay for good pricing. I would say approx. $200-$250 for a…
Posted on: 10/09/2017
Owner: Miguel Arroyo Year: 1999 Model: Maxima Color: Custom Candy/Pearl Tangerine Orange Transmission: Manual 5spd Trim: SE-L also known as 99.5 or 4.5 Gen What motivated you to MOD your Maxima? I've been a Nissan guy all my life and I love the body style specifically on this model, it's also…
Posted on: 01/08/2017
Member Credit: TC from Zmods Tools Required: - Z32 front caliper rebuild kit - 14MM Socket & ratchet - Torque wrench - Bench Vice - Air Compressor - Fine tipped awl - Bench grinder with a wire wheel - 2 cans of brake cleaner - Acetone or lacquer thinner -…