| Results 1 - 30 of 299 | Page 1 of 10 |
| Results per-page: 10 | 20 | 50 | 100 |
Relevance: 100% Posted on: 01/15/2017
Member Credit: Freeengineinfo Idle Air Control Valve Replacement Does your car idle rough or the speed cycle up and down. You probably have a bad idle air control valve. The only purpose of the idle air control valve is to keep the engine’s idle smooth. The engine’s computer gives the…
Relevance: 93% Posted on: 02/13/2021
Community Member Credit: R&D Factory Here are DIY instructions on how to replace the OEM seals on your Nissan VQ engine. At R&D Factory, we service many Nissans and Infiniti's daily and run into the same valve cover/spark plug o-ring leak. About 75% of the vehicles that we serve have…
Relevance: 89% Posted on: 09/02/2019
Member Credit: EddyMaxx Our 2009 7thgen Nissan Maxima threw code P0075 - Intake Valve Control Solenoid Circuit (Bank 1). Bank 1 is the location closest to the Firewall. The first thing to always do is to check the connectors and harness to see if it's broken or has any exposed…
Relevance: 82% Posted on: 01/08/2017
Member Credit: scrui Lift the front end of the car about two feet, high enough for you to get underneath and have easy access. I used ramps. Please make sure car is lifted safely so there's no serious injuries. Drain oil from transmission, use an Allen key to remove plug. Remove…
Relevance: 74% Posted on: 02/16/2020
Member Credit: sdot82 This write-up is for a 2000-01 VI manifold swap on to 95-99 Maxima. There are many ways to do this swap so first I will number the ways I know how to do this and then go into detail on how to do it. There are a…
Relevance: 73% Posted on: 03/17/2018
Member Credit: Anthony Carter Tools Needed: Hard Plastic Blade to Remove Shifter Cover and Bent Box (Flathead may mess up your dash) #2 Phillips Small Phillips Small Flathead to help disconnect electrical connectors in back of climate control unit 8mm Socket w/ Extension. Pop out the vent up top. Pop…
Relevance: 62% Posted on: 01/08/2017
Member Credit: rpsuprdave WARNING: It is not recommended that you attempt this procedure without basic mechanical skills and knowledge of automobiles. Always take safety precautions seriously when working around an automobile. A simple mistake may cause you physical harm and/or death. Improper installation may cause mechanical damage to the vehicle. Materials…
Relevance: 60% Posted on: 01/10/2021
Community Member Credit: Benzolorenzo1 About 6 months ago I received the death code P1778 (stepper motor) in my 2008 Altima. I searched far and wide, low and high, only to be told 2 things... you need a new transmission, or you need a new valve body. Since I didn't have…
Relevance: 59% Posted on: 01/20/2018
Member Credit: cfr94 This installation process is for a set of Eibach Suspension Springs Pro Kit 6369.140 with 2.0" drop in front & 0.8" drop in rear. REAR END: 20-30 minutes Tools Needed: Air rachet or air gun, 18mm socket 3/4" open wrench & adjustable floor jack These instructions are…
Relevance: 56% Posted on: 01/01/2018
Member Credit: Cheston WARNING: These are JUST directions. I am NOT liable if you mess up your car. Use common sense when attempting this or ANY mod. Always use caution when it comes tools that use electricity. WEAR PROTECTIVE CLOTHING! Tools needed: phillips & flat head screwdriver, 10mm socket, 12mm socket,…
Relevance: 56% Posted on: 12/28/2017
Member Credit: Julian Nicasio If you are looking to replace your engine covers, below are the part numbers you need. Below is the current pricing as of December 2017. You can buy them on eBay, NissanPartsDeal.com, quirkparts.com, rockauto.com. Engine Cover 14041-9N00B $78.09 Upper Cover 64894-9N00A $50.87 Fuse box Cover 24382-ZY70A $11.28 Upper…
Relevance: 53% Posted on: 09/22/2019
Member Credit: Cdg2125 Tools Required: Ratchet 10m socket 12mm socket Flathead or 8mm socket Pliers or vise grips 1 can of Throttle Body cleaner 1 can of Carb cleaner (I find Berrymans B12 to work fastest) New throttle body gasket New IAC Valve Gasket (dealer only) Step 1: Disconnect battery.…
Relevance: 52% Posted on: 01/14/2018
Member Credit: Bryan Tisch Below are the procedures that I used in performing the replacement of six of my fuel injectors. I put them on this web page to serve as guidance for you, but do not guaranty the results nor do I proclaim this is the correct procedure, though I reference…
Relevance: 51% Posted on: 01/25/2018
Member Credit: shift_ice Installation procedure: 1) Remove the kick panel underneath the steering wheel. There are 2 screws at the bottom of the trim and snaps at the top. Get the screws removed and pull towards the rear of the car to release the snaps. 2) Disconnect the dimmer (and…
Relevance: 50% Posted on: 12/29/2017
Member Credit: Ghozt Here are instructions for how to remove your front bumper fascia, or what many of you simply know as the front bumper of your car. One note: if you have the Stillen lip installed 2 of the screws on the bottom will be covered and only accessible…
Relevance: 48% Posted on: 12/25/2017
Member Credit: Greg Changing the spark plugs on a 2002-2003 Maxima is not something you should have to do until around 100,000 miles. The stock plugs are platinum tipped and should last a very long time. Replacement of the plugs is something that Nissan recommends you "see your dealer" to…
Relevance: 48% Posted on: 09/04/2020
Facebook: Rabbit Hole Motorsports Photo Credit: Rene Saran, Jose Vargas, Rabbit Hole Motorsports Order Link: https://rabbitholemotorsports.bigcartel.com/product/push-in-pcv-fitting-8an Push-In -8AN fittings to accommodate the 5/8" PCV tube found on VQ engines valve covers to clean up your Oil Catch Can setup. These are AN fittings designed to be pushed in your engine…
Relevance: 47% Posted on: 12/07/2019
Member Credit: Ronny Para This article will help you install Audi R8 Coil Packs on your VQ30DE. For those that don’t know, Audi coilpacks are stronger and better than Nissan coilpacks. They add better mpg and more HP/TQ. It works on bone stock vehicles or highly modified vehicles. Nissan Coilpack…
Relevance: 45% Posted on: 09/17/2020
Community Member Credit: Nismo3112 / vsamoylov Important Notes: You will need the front valve cover from a 350z and modify the plenum to clear the hood. The FWD fwd valve cover on the driver's side won't work cause of the oil plug. The Front Strut Bar does fit You can use…
Relevance: 45% Posted on: 01/15/2017
Member Credit: speed racer These were the tools used: 1. Philip Screw Driver 2. Dremel with cutting accessory 3. Needle Nose pliers 4. Hair Tweezers 5. 10mm socket In this picture you can see where the two small screws hold the valve plate. You really only have one shot of…
Relevance: 43% Posted on: 01/06/2019
Member Credit: G35 Mass I installed LFR5AIX-11 plugs. First, the tools you will need: 6 NGK Iridium IX Sparkplugs 3/8" Rachet 3/8" long extension (at least ten inches) 10mm socket 10mm open-end wrench 16mm "deep" socket (or "sparkplug socket") Magnetic pick up tool 3-prong grabber (optional, you'll need it if you don't have a…
Relevance: 42% Posted on: 11/18/2018
Member Credit: EddyMaxx Over the past few weeks, there's been a strong gasoline smell coming from the driver side. I almost thought it was a gas leak since I had a tiny pinch in exhaust pipe which was leaking some condensation / water. Upon scanning it for codes I found…
Relevance: 42% Posted on: 01/01/2018
Member Credit: pmohr This howto is for the quick and easy task of replacing the ignition switch. If you have to jiggle the key around for the car to start, have to do any special tricks for it to work, whatever. This whole process shouldn't take but 10 minutes, if…
Relevance: 42% Posted on: 12/25/2018
Owner: Steve Fernandez aka 98MaXedOut Year: 1997 Model: Maxima Color: White Transmission: 5-Speed Manual Trim: SE Mod List: 2003 Modded VQ35 with 3.0 timing 5-Speed Transmission w/ LSD ARP Rod bolts ARP Main Bolts ARP Head studs 350z Revup Cams PnP LIM HR Valve Springs and retainers double shimmed (can safely rev to 8k) Revup Oil…
Relevance: 41% Posted on: 08/18/2017
Member Credit: 99BlackMaxMS So upon installation of the kit, my car developed a small oil leak that turned worse as time passed. It started after installing the supercharger, so I tried everything possible. I replaced sandwich plate & fittings, feed line fitting and eventually after pulling the blower, I saw that…
Relevance: 40% Posted on: 08/29/2020
This is just a reference photo of where do find your fuel pump relay on 02-03 5thgen Nissan Maxima's. The location of the fuel pump relay is right under the hood release to the left of where your footrest is. You will need to remove the plastic cover, a sticky…
Relevance: 39% Posted on: 05/17/2020
Credit: Fezzik (David Honey) This is the How To on the installation of heated mirrors. A few things first before I go on. I have the automatic climate control with the rear window defogger switch on it. The side view mirrors are linked to this switch. For those with manual…
Relevance: 39% Posted on: 02/10/2018
Member Credit: Sparky This 2006 Nissan Maxima came in with the complaint that the gauges and the a/c controls did not work. After the obvious fuse checks I went to the most common location for this problem in Nissan Maximas. The problem is located behind the a/c control panel and…
Relevance: 39% Posted on: 02/06/2017
Full Package Pricing $175 shipped This is a Send In Service I can also Supply a Cluster and Climate control for an Additional $55 Parts Included in Send in led Mod Package Includes the following: Cluster Climate Control 4 Door Switches All Dash Buttons and Controls Single Color ONLY! Optional:…
Relevance: 39% Posted on: 01/23/2018
Member Credit: Mishmosh Typically, the water pump will need to be removed due to the water pump failing or the water pump O-ring seals (2) failing with age. You may get coolant leaking from the weep hole toward the front of the engine with the inner seal failing. Some will…