| Results 1 - 30 of 98 | Page 1 of 4 |
| Results per-page: 10 | 20 | 50 | 100 |
Relevance: 100% Posted on: 09/27/2020
If you are not able to scan your car for codes, make sure to check the 10AMP fuse inside your car under the driver dash. If this fuse is blown, it will not allow you to use your ODB2 scanner to check for codes. It's the BAT 10A - Electronic…
Relevance: 80% Posted on: 01/26/2018
Member Credit: EddyMaxx I was getting all of these codes at once. Before replacing anything, I decided to do some simple diagnostics and checks. I checked my 02 Sensor Fuse and surely it was BLOWN. I replaced the fuse and all these codes were gone. No more P1148, P1168, P1031…
Relevance: 77% Posted on: 12/02/2019
Member Credit: maxiiiboy Symptom (when turning the ignition switch to START) Likely Cause No Crank, No Nothing (not even dashboard lights) If the car starts with a boost, then the battery is bad. If not, suspect the ignition switch, the battery cables, fuses, or ground/power distribution. No Crank, just a…
Relevance: 53% Posted on: 12/17/2020
Community Member Credit: 96SEmaxB So I started blowing this in cab 10amp fuse called meter, I checked alternator, battery, called harness lights all the normal stuff, couldn't find it, meanwhile that fuse controls the cluster and puts the vehicle into fail-safe mode... so I scoured the forums and google and…
Relevance: 48% Posted on: 05/25/2019
Member Credit: Nikky Nixmax A few days ago, I went to start my 2009 Nissan Maxima in the evening. I came to find out that the car would not start. Initially, I thought it was the battery so I switched it with another car. Same results.... car would not just…
Relevance: 47% Posted on: 11/17/2018
Member Credit: EddyMaxx I had recently encountered a Brake/Battery Light. The alternator checked out OK and car was driving well. After a little research, I discovered that the 10A Alternator Fuse located in the engine bay (picture below) was blown. Once I replaced it, both the Battery and Brake Light went…
Relevance: 40% Posted on: 01/01/2018
Member Credit: pmohr This howto is for the quick and easy task of disabling/removing the stock buzzer underneath the dash. Personally I disabled it because I tend to use the headlights to light things up at night, and the beeping with the door open drives me crazy. This whole process…
Relevance: 39% Posted on: 09/10/2020
Community Member Credit: Eddy I decided to install an Audi Battery Power Jump/Terminal Box. The engine bay is so much cleaner and I can now jumpstart the car from the engine bay vs the trunk if I ever need to. You can also see where I put the OEM battery…
Relevance: 38% Posted on: 06/23/2020
Member Credit: myer84 I finally finished installing my last mod. For a while I’ve been searching for a shift light indicator, but nothing as big as a Monster Tach or anything that would make the car look ricey. My idea of a shift light was something that would be small…
Relevance: 36% Posted on: 12/07/2019
Member Credit: TunerMax I had a free SMD LED board from HIDextra and decided to install some under hood lighting, something they should have done at Nissan. Thought I'd share this with you guys I'm sure there are quite a few of you that would be very interested in doing…
Relevance: 35% Posted on: 06/16/2019
Member Credit: DennisMik This mod provides power all the time, with doors open or closed. I have this irritating habit of forgetting to close the rear windows and I didn't like having to put the key in the ignition and turn it on in order to operate the power windows.…
Relevance: 35% Posted on: 01/01/2018
Member Credit: Cheston WARNING: These are JUST directions. I am NOT liable if you mess up your car. Use common sense when attempting this or ANY mod. Always use caution when it comes tools that use electricity. WEAR PROTECTIVE CLOTHING! Tools needed: phillips & flat head screwdriver, 10mm socket, 12mm socket,…
Relevance: 33% Posted on: 01/10/2018
Member Credit: Orgullo This is the battery relocation for the 2002/2003 Nissan Maxima. However, I'm sure it will work for the other gens too since it's basically the same. I did this on my 5.5 and my boys 5.5 gen Max. This set up is for people that already have a…
Relevance: 33% Posted on: 06/21/2020
This post if for folks looking to install SPAL Fans into their Maxima. These are quality high-speed fans that are great for both N/A and Boosted Setups. PDF Instructions: SPAL Fan Wiring Overview: We designed the SPAL fan wiring harness to enable the simplest installation of our performance fans. It…
Relevance: 33% Posted on: 11/29/2019
Member Credit: Metal Maxima This is the second section of my electrical system upgrade. You can read the first part, how to upgrade the OEM ground wire, here. This how-to will be covering the details on how to perform the upgrade known as the 'Big Three'. Essentially, it will yield…
Relevance: 33% Posted on: 01/24/2018
Member Credit: shift_ice The fogs can easily be rewired to allow them to be run without the headlights. The fog light switch on the turn signal stalk still continues to turn the fogs off and on as before - the only difference is the fogs can be turned on without…
Relevance: 32% Posted on: 02/10/2018
Member Credit: Sparky This 2007 Nissan Maxima came in with the complaint that the gas gauge was stuck on empty. Actually a closer look revealed that the gauge needle was stuck under the empty stop peg. Due to the coloring of the instrument cluster lens I was unable to get…
Relevance: 31% Posted on: 10/28/2020
Community Member Credit: boredmder Replacing the heater pipes on a 4th gen Nissan Maxima. Dash removal is not required, as long as you can work in a tight space. https://www.youtube.com/watch?v=ZBw-rqTB604 https://www.youtube.com/watch?v=VuJASXZU1kQ
Relevance: 30% Posted on: 01/28/2018
Member Credit: 05ALTIMASE-R & Earl Johnson The key to this install is basically taking the 2 wires from the fog light switch on stalk and cutting them out of the OEM circuit. Then taking the two wires and putting one to a ground and running the other into the engine compartment to the IPDM (relay/fuse block). The last step is pulling the…
Relevance: 30% Posted on: 06/07/2018
Article Credit: EddyMaxx The videos below show you the best way to remove and replace your ABS actuator pump. It is very important that you use the SAME EXACT part number as your old one to avoid any issues. You can find them used on eBay or junkyard. I was…
Relevance: 29% Posted on: 07/22/2020
Credit: DennisMik I would like to start by thanking JNCoRacer for his motivational pep talk. He was smart enough to know that I could do it, even though I didn't think I could. Thanks man. You will need various standard tools: screwdrivers (Phillips for screws & flat for prying), wire…
Relevance: 29% Posted on: 11/30/2020
Community Member Credit: DAlastDON When I bought my 07 maxima one of the things that sold me on the car was the intelligent key fob. Its nice to not have to dig in my pocket to get my keys out. Just walk up push the button on the door handle…
Relevance: 27% Posted on: 12/29/2018
Member Credit: steeds Here is the P.Side all tucked with the fuse box still in the engine bay. Just for info on how to remove the Anti Skid Control Actuator clip. Pull the handle out like a drawer and it will release the clip. After tucking the wires on the P.Side…
Relevance: 27% Posted on: 02/10/2018
Member Credit: Sparky This 2006 Nissan Maxima came in with the complaint that the gauges and the a/c controls did not work. After the obvious fuse checks I went to the most common location for this problem in Nissan Maximas. The problem is located behind the a/c control panel and…
Relevance: 26% Posted on: 02/06/2017
Full Package Pricing $175 shipped This is a Send In Service I can also Supply a Cluster and Climate control for an Additional $55 Parts Included in Send in led Mod Package Includes the following: Cluster Climate Control 4 Door Switches All Dash Buttons and Controls Single Color ONLY! Optional:…
Relevance: 26% Posted on: 09/27/2020
Engine Bay (By Battery Tray) Interior (Under Driver Dash)
Relevance: 26% Posted on: 12/28/2017
Member Credit: Julian Nicasio If you are looking to replace your engine covers, below are the part numbers you need. Below is the current pricing as of December 2017. You can buy them on eBay, NissanPartsDeal.com, quirkparts.com, rockauto.com. Engine Cover 14041-9N00B $78.09 Upper Cover 64894-9N00A $50.87 Fuse box Cover 24382-ZY70A $11.28 Upper…
Relevance: 25% Posted on: 03/11/2018
Member Credit: Chris Goss In my 08, I put the heated steering wheel switch to the left of the steering wheel just because it was easier and shorter wire runs. Run a wire from the battery with an waterproof inline fuse holder with a 10a fuse in it. Connect that…
Relevance: 25% Posted on: 12/23/2017
Member Credit: TEQ-NIQ Step 1: Remove shifter knob - Shifter knob is made of two parts, the leather handle, and the lower aluminum-looking cone-shaped piece. Grasp the cone-shaped lower piece, rotate counter-clockwise and pull down at the same time to release from shifter handle. Once this is done, there is a…
Relevance: 25% Posted on: 12/23/2017
Member Credit: jsmithsole This is for those who would like to install the 7thgen Mirrors on their 6thgens. Considering they are from a different car the fit really well, not perfect but pretty damn close! The holes for the new mirrors do not match up so all 3 need to be…