| Results 1 - 30 of 88 | Page 1 of 3 |
| Results per-page: 10 | 20 | 50 | 100 |
Relevance: 100% Posted on: 11/25/2018
Member Credit: Matty Here is a list of parts you will need if you plan on purchasing my V1 Starter Kit and want to finish off the kit with custom items. Vortech V1 or V2 Blower (Counter Clockwise Rotation, Straight Discharge) The blower NEEDS to have this fitting on it…
Relevance: 96% Posted on: 12/25/2017
Member Credit: Greg Changing the spark plugs on a 2002-2003 Maxima is not something you should have to do until around 100,000 miles. The stock plugs are platinum tipped and should last a very long time. Replacement of the plugs is something that Nissan recommends you "see your dealer" to…
Relevance: 85% Posted on: 08/01/2020
Credit: EddyMaxx My rear brake line on 4thgen Nissan Maxima had a pinch in it and caused brake fluid leak. I was going to replace with another stock line but ended up ordering stainless steel brake lines from eBay. You get all 4 brake lines shipped for $67 bucks which…
Relevance: 83% Posted on: 01/21/2017
Member Credit: shift_ice Over time the brake system can take on air as the effectiveness of the brake fluid decreases with age. Air can also enter the system from a leaky brake hose, a bad connection on the brake caliper, during any maintenance when a brake line is removed, or…
Relevance: 82% Posted on: 09/22/2020
Blehmco Kit: Z32 Calipers 2004 6thgen Maxima Rotors Relocation brackets Conversion Lines Jeff92se Kit: z32 calipers Cobra rotors relocation brackets center rings conversion lines Z32 Direct Rotor Swap: Z32 calipers Z32 rotors (must be milled down) conversion lines. Additional Info: You have to mill down the diameter of the rotor,…
Relevance: 75% Posted on: 01/10/2018
Member Credit: Orgullo This is the battery relocation for the 2002/2003 Nissan Maxima. However, I'm sure it will work for the other gens too since it's basically the same. I did this on my 5.5 and my boys 5.5 gen Max. This set up is for people that already have a…
Relevance: 68% Posted on: 01/13/2018
Member Credit: Ken Rosengren FAQ Q) What does a knock sensor do? A) A knock sensor is a specially designed listening device for car engines. It listens for engine knock, or detonation (pinging). Detonation can be very bad for an engine and is the result of the fuel/air mixture exploding too…
Relevance: 60% Posted on: 01/05/2017
Source Credit: EddyMaxx These are instructions on how to install a wet nitrous kit in your 6thgen. This is pretty straight forward but if you have any doubt please take it to someone who knows how to install these systems. The Zex model used for 6thgens is usually the 82016…
Relevance: 56% Posted on: 01/13/2018
Owner: Nick Gopaul Social Media: Year: 1995 Model: Maxima Color: Black Emerald (DJ2) Transmission: Manual 5-Speed Trim: SE What motivated you to MOD your Maxima? I’ve always loved the Nissan Maxima…specifically the 4th gen. When the 4th gen was first released in 1995, I liked it from then. When the first…
Relevance: 56% Posted on: 06/30/2018
Member Credit: EddyMaxx I recently replaced the ABS Actuator on my 2004 Nissan Maxima. Since the job requires removing the brake hard-lines, you will need to bleed all of your brakes to get all the air pockets out. Easy enough right?? Well....... I bled the brakes 4-5x times and the…
Relevance: 52% Posted on: 01/14/2018
Member Credit: Bryan Tisch Below are the procedures that I used in performing the replacement of six of my fuel injectors. I put them on this web page to serve as guidance for you, but do not guaranty the results nor do I proclaim this is the correct procedure, though I reference…
Relevance: 50% Posted on: 12/28/2017
Member Credit: Joshua Wright Here I will outline everything you will need to purchase to successfully install the Akebono brakes/calipers on our 7thgen Maxima. First (Acquisition of Calipers): Obviously, you will need to get you a set of Akebono calipers. You can get any of them from the following vehicles since…
Relevance: 50% Posted on: 01/05/2017
Community Member Credit: DeusExMaxima The procedure for removing the OEM intake and replacing it with the Kinetix was fairly straightforward. With basic hand tools, I did the job at a casual pace in under 2 hours. Tools Needed: Allen wrench (supplied with manifold) 10mm, 12mm, and 14mm wrenches and sockets…
Relevance: 49% Posted on: 10/19/2020
Community Member Credit: iansw So I've been asked to do a write-up on how to make the Z32 MAF setup work with the JWT ECU + 370cc Injectors while Supercharged on the charged side. Symptoms: With the Z32 MAF on the charged side and stock Stillen piping the car idles…
Relevance: 46% Posted on: 09/20/2020
Community Member Credit: Josh Go Hard Neal BlackPath's Caliper Kit allows the installation of larger 300ZX calipers and 12.75" 350Z rotors (not included) on your Nissan Maxima. The bracket is made for a 240SX but also fits your 4thgen or 5thgen Nissan Maxima. Important Note: You will need the 350z…
Relevance: 43% Posted on: 06/03/2018
Member Credit: Fuzzyknub / EddyMaxx If you eliminate your EGR valve, you'll likely get a P0400 Exhaust Gas Recirculation Flow Malfunction trouble code. But no worries, here's what you need to do to get rid of the code. EGR (What you will be eliminating/deleting) 1. EGR Block-off Plate Buy the EGR blockoff plate…
Relevance: 42% Posted on: 12/29/2018
Owner: Matt Faraca aka airmattdog Year: 1997 Model: Maxima Color: Lamborghini Orange Paint Transmission: Automatic Trim: SE Mod List: Engine: Injen Polished Cai Custom Polished Valve Cover Polished Ac Lines Polished Brake Lines Custom Polished Aluminum Relay Covers Custom Polished Maf Sensor Cover Cusco Polished Oil Catch Tank Weapon R Polished Coolant Tank Nismo Oil…
Relevance: 42% Posted on: 02/08/2017
Member Credit: Tavarish aka Freddy This how-to depicts how I did the swap. I am by no means responsible for what you do to your car, and any ill effects are your responsibility. I take credit in writing this how-to, and please do not use it without the author’s permission.…
Relevance: 41% Posted on: 11/11/2019
Member Credit: sparky1562 The Issue Left work Friday afternoon everything was okay. No signs of previous issues, no codes. Sitting at a stoplight the car started shaking real bad, hit the gas to go and she kept running but very rough. The check engine came on. I went to blinking…
Relevance: 39% Posted on: 06/07/2018
Article Credit: EddyMaxx The videos below show you the best way to remove and replace your ABS actuator pump. It is very important that you use the SAME EXACT part number as your old one to avoid any issues. You can find them used on eBay or junkyard. I was…
Relevance: 39% Posted on: 12/25/2018
Member Credit: 95BLKMAX I wanted bigger brakes, but I didnt want to spend a fortune (as much as one would spend, say for a Z32 upgrade, or the 6th gen rotors with Z32 calipers, etc...) for just front brakes. Plus I dont autoX, I just do alot of highway spirited driving;…
Relevance: 38% Posted on: 01/20/2018
Member Credit: MissMiami Below are the most commonly asked questions before starting this conversion. This very similar to getting the hybrid bumper which allows you to retain 2004-2006 Headlights/Hood with 2007/2008 Bumper. "Where did you get your 2007 bumper?" I got mine on eBay for about $50.00 on eBay, with about $50.00…
Relevance: 38% Posted on: 02/24/2018
Member Credit: EddyMaxx & Michael Bird Tindal Thanks to Michael for posting this information. For approx. $300 bucks, you can have a front Akebono BBK on your 7thgen Maxima. This is for only the Front BBK ONLY. You can do the rear setup as well inexpensively. This is applicable to other…
Relevance: 38% Posted on: 10/21/2020
Community Member Credit: vipervadim Another Project from 2014 6gen brakes swap into 4th gen Maxima that clear 16in rims I've seen plenty of 6th gen brake swaps into 4th/5th gens but I've never seen them modified to clear 16in rims. I have 16s, spring and stuts, I plow through potholes…
Relevance: 37% Posted on: 01/15/2017
This applies to 2000-2001 5thgens. VIAS stands for Variable Intake Air System. It is made up of a power rod going through your intake manifold that holds a series of butterfly valves. A solenoid turns the rod at 5000 rpm to open the valves to allow the engine to breathe…
Relevance: 35% Posted on: 12/17/2018
Member Credit: The Wizard & ptatohed As a few of you know, ptatohed (Josh) and myself (James) recently installed a water to air aftercooler on his car. After doing a lot of homework, we decided on a 'barrel design' (as opposed to a 'box' design). We ended up going with the…
Relevance: 35% Posted on: 01/15/2017
Member Credit: Greg 1.I bought the Hayden model 404 from Pep Boys for $49.99 plus tax. There were other smaller models, but I figured I would get the largest one practical. The 404 is considered "Heavy Duty" and is 7.5 inches tall by 15.5 inches wide, by 0.75 inches thick.…
Relevance: 35% Posted on: 12/28/2017
Owner: Dan Evans Year: 2009 Model: Maxima Color: Radiant Silver (K12) Transmission: Manual 6 Speed Trim: Sport/Tech Trim What motivated you to MOD your Maxima? I joined maxima.org in November 2010 and after that my bank account never forgave me. - Dan Evans https://youtu.be/p1gucLyRRyU https://youtu.be/waXka7l34FM https://youtu.be/IrEqPzVXdik Full Mod List / Specs:…
Relevance: 34% Posted on: 01/01/2018
Member Credit: Viper Vadim I've seen plenty of 6th gen brake swaps into 4th/5th gens but I've never seen them modified to clear 16in rims. I have 16s, spring and stuts, I plow through potholes in NYC, I'm never going to drive low and SLOW and avoid all potholes like some…
Relevance: 33% Posted on: 12/29/2017
Member Credit: twin001 This write-up is for a 2003/2004. But the same steps are application to 6thgen Maxima. Also, for 7thgens you do not need brackets but the installation instructions still hold. This DIY will take you through the basic steps to remove the existing brake components (calipers, rotors, lines) in…