Search Results for: Led resistors

Results 1 - 14 of 14Page 1 of 1
Results per-page: 10 | 20 | 50 | 100

How to Install Tail-As-Turn Mod on 7thgen Nissan Maxima

Relevance: 100%      Posted on: 01/26/2018

How to Install Tail-As-Turn Mod on 7thgen Nissan Maxima

Member Credit: Candelario Amaya Jr With this simple power control module, you can convert any LED tail lamp to also function as the turn signal, for a much more modern appearance. It will work very well in any vehicle where the turn signal is a traditional filament bulb. To install this…

How To Install Resistors (If You Have Hyper-flashing LED Tails, Switchbacks or Turn Signals)

Relevance: 86%      Posted on: 12/23/2017

How To Install Resistors (If You Have Hyper-flashing LED Tails, Switchbacks or Turn Signals)

Member Credit: EddyMaxx, Blaxima06, Jsmithsole If you are experiencing hyper-flashing after installing Ezkoncepts LED Tail Lights, LED Turn Signals and/or Switchbacks, then you will need to install resistors to eliminate it. You can choose to either install them directly on your tail lights or headlights. It's up to your preference. Both…

How to Fix Your Spoiler LED Light on 4thgen Nissan Maxima

Relevance: 76%      Posted on: 02/21/2021

How to Fix Your Spoiler LED Light on 4thgen Nissan Maxima

Community Member Credit: ZaxWhite97Max Recently I swapped trunk lids with one with a spoiler. And to my unpleasant surprise the LED strip on the spoiler did not work. I got on and searched and searched, Looked through the how-to's and couldn't find anything. Although someone did mention that the resistors

How to Install LEDs on Hazard/Defroster

Relevance: 65%      Posted on: 01/01/2018

How to Install LEDs on Hazard/Defroster

Member Credit: wariow3 This is a how-to to change the current lights in the Hazards and Rear Defroster buttons. This application is for 95-99 Maxima's but might work also for other max's and cars. Thanks to JackBauer for his help on the hazards and rear defroster. Difficulty: Easy to moderate.…

How to Change Bulb Light in the Dome Light to LED

Relevance: 62%      Posted on: 01/01/2018

How to Change Bulb Light in the Dome Light to LED

Member Credit: wariow3 Difficulty: Easy to moderate. Knowledge of LED's + Resistors Experience with soldering recommended Items needed: Small flat head screw driver small phillips screwdriver 5mm leds ,I used white LED's( around 10, more just incase they blow or just dont' work) I get mine off ebay from the…

Swapping 2016-2018 8thgen Nissan Maxima Headlights / Tail Lights to 2019+

Relevance: 59%      Posted on: 02/25/2019

Swapping 2016-2018 8thgen Nissan Maxima Headlights / Tail Lights to 2019+

Member Credit: Angel Peña, Jose Rivera & Azeem Malik When you first glance at the 2019 Nissan Maxima, you’ll quickly take notice of the updated exterior headlights and tail lights. Now if you already own a 2016-2018 8thgen you've likely already asked the big question.... will the 2019+ Maxima headlights…

Nissan Maxima Knock Sensor Bypass Resistor using 470K Resistor

Relevance: 53%      Posted on: 09/20/2020

Nissan Maxima Knock Sensor Bypass Resistor using 470K Resistor

Community Member Credit: asand1 / maxima_se007 Important Note: This should really be used as a temporary solution. The proper fix is to replace either the knock sensor itself or the harness which is known to go bad. Most people do both at the same time. Resistor: 470K Order Link: https://www.radioshack.com/products/radioshack-470k-ohm-1-2w-5-carbon-film-resistor-pk-5?variant=20332249541…

How to Install LEDs on Auto Climate Control

Relevance: 41%      Posted on: 01/01/2018

How to Install LEDs on Auto Climate Control

Member Credit: Zach Brown Disclaimer: I will take no responsibility to any damage done to your vehicle by attempting this mod. I recommend only people with at least some electrical background and soldering skills attempt this. You could very likely blow up either LEDs or your Climate Control by doing things incorrectly.…

How to Swap the Gauge Needle Color on 4thgen Maxima

Relevance: 39%      Posted on: 01/01/2018

How to Swap the Gauge Needle Color on 4thgen Maxima

Member Credit: wariow3 Difficulty: Moderate. Knowledge of LED's + Resistors Experience with soldering recommended Items needed: Small flat head screw driver small phillips screwdriver 5mm leds ,I used white LED's( around 4 or more, one for every gauge, more just incase they blow or just dont' work) I get mine…

Corey Mott’s 2005 6-Speed Nissan Altima SE-R (Modded & Tuned 269WHP)

Relevance: 25%      Posted on: 07/18/2020

Corey Mott's 2005 6-Speed Nissan Altima SE-R (Modded & Tuned 269WHP)

Owner: Corey Mott Year: 2005 Model: Altima SE-R Color: Smoke Metallic Engine: VQ35DE Transmission: 6-Speed Manual Mod List: Ionic Dynamics Carbon Fiber Engine Cover Mishimoto Catch Can Mishimoto Radiator Mishimoto Oil Cap Mishimoto Carbon Fiber Radiator Cap Mishimoto Power Steering Reservoir Moog Front Sway End Links Moog Rear Sway End Links…

How to Install Door Handle LEDs

Relevance: 20%      Posted on: 01/08/2017

How to Install Door Handle LEDs

Member Credit: Wildman04 I did the rear door first and the rear doors are a lot easier than the front doors are to do. The rear doors will take around 45 minutes to an hour and the front doors about two hours each, so probably allow a good day for…