Search Results for: Hot sTart

Results 1 - 30 of 152Page 1 of 6
Results per-page: 10 | 20 | 50 | 100

Reset Blinking Airbag Light on 2009-2015 Maxima

Relevance: 100%      Posted on: 10/08/2017

Reset Blinking Airbag Light on 2009-2015 Maxima

If you've recently installed a radio, seats or any other sensitive electronics you may have triggered you're air bag light. It typically just flashing on and off once it is trigger. But no worries. The procedure below will help you reset. We've tried this procedure various times and works perfect. …

Infiniti I35 / 5thgen Nissan Maxima No Start Condition Due to Lock Mode (FIX INSIDE)

Relevance: 82%      Posted on: 10/20/2020

Infiniti I35 / 5thgen Nissan Maxima No Start Condition Due to Lock Mode (FIX INSIDE)

LOCK MODE FUNCTION When the starting operation is carried out five or more times consecutively under the following conditions, IVIS (NATS) will shift the mode to one which prevents the engine from being started. - Unregistered ignition key is used. - IMMU or ECM’s malfunctioning. ESCAPE FROM LOCK MODE 1.…

P1610 NISSAN – Lock Mode (5thgen Maxima Won’t Start)

Relevance: 69%      Posted on: 02/11/2018

P1610 NISSAN - Lock Mode (5thgen Maxima Won't Start)

This seems to be common on the 2002-2003 Nissan Maxima's. Below is a procedure you can follow before going to the dealer. Possible causes: Faulty or not programmed ignition key Faulty IMMU Faulty Engine Control Module (ECM) This code is usually triggered when a not registered or damaged key is…

5thgen Nissan Maxima Quick Guide to No-Start Problems

Relevance: 63%      Posted on: 12/02/2019

5thgen Nissan Maxima Quick Guide to No-Start Problems

Member Credit: maxiiiboy Symptom (when turning the ignition switch to START) Likely Cause No Crank, No Nothing (not even dashboard lights) If the car starts with a boost, then the battery is bad. If not, suspect the ignition switch, the battery cables, fuses, or ground/power distribution. No Crank, just a…

How to Perform Idle Air Volume Learning Procedure

Relevance: 46%      Posted on: 01/15/2017

How to Perform Idle Air Volume Learning Procedure

This applies to the 2000-2001 5thgens. Before performing Idle Air Volume Learning, make sure that all of the following conditions are satisfied. Learning will be cancelled if any of the following conditions are missed for even a moment. Battery voltage: More than 12.9V (At idle) Engine coolant temperature: 70 -…

2004 Nissan Maxima P0335 Trouble Code (Crankshaft Position Sensor)

Relevance: 46%      Posted on: 06/04/2018

2004 Nissan Maxima P0335 Trouble Code (Crankshaft Position Sensor)

Member Credit: EddyMaxx I was getting the following code: P0335 Crankshaft Position Sensor A Circuit Malfunction  This code was causing my car to go into "limp mode" and wouldn't go over 3500 RPM. Also, don't confuse this sensor with the Camshaft Position Sensor. The sensor is very easy to change. All…

How to Perform ECU Reset, Throttle Pedal Release, TVCP, Idle Volume Learning

Relevance: 45%      Posted on: 01/15/2017

How to Perform ECU Reset, Throttle Pedal Release, TVCP, Idle Volume Learning

This applies to 2002-2003 5thgens. Member Credit: maxima dude Before attempting any of the following procedures, it is advisable that you read through the instructions thoroughly and familiarize yourself with them. A stop watch or an analog clock with a second’s needle will be useful. ( i counted outloud becuz…

2004+ 6thgen Nissan Maxima P0340 – Bank 1 Cam Positioner Sensor Fix

Relevance: 44%      Posted on: 06/15/2020

2004+ 6thgen Nissan Maxima P0340 - Bank 1 Cam Positioner Sensor Fix

Member Credit: CXJ Performance I went to start my car using the auto start and it stalled. I got the car checked and it threw code P0340 Camshaft Bank 1 Position Sensor Malfunction. Below is my guide to the repair. Symptoms Car hesitates to start Car manual mode is stuck…

Adjust Throttle Position Sensor (TPS) on 4thgen Nissan Maxima

Relevance: 44%      Posted on: 05/08/2021

Adjust Throttle Position Sensor (TPS) on 4thgen Nissan Maxima

Community Member Credit: vbxmaxima Well, if you're here, you are probably experiencing some trouble because the TPS is not a regular maintenance item! Unfortunately, TPS failure seems rather common. It's happened to me, and I see it in one to two other Maxima enthusiasts a year. Heck when Edmunds.com was…

How to Remove your 6thgen Headlights

Relevance: 43%      Posted on: 02/10/2017

How to Remove your 6thgen Headlights

Member Credit: Elite Package Hey guys i just recently painted the interior of my lights black to match my car. I just figured i'd write this post to help anyone out by giving "visual" instructions rather then "Text" instructions. So if you decide to tackle this project yourself like i did,…

Ecliptech Sequential RPM Shift-P2 Light Installed on 5thgen Nissan Maxima

Relevance: 42%      Posted on: 10/24/2020

Ecliptech Sequential RPM Shift-P2 Light Installed on 5thgen Nissan Maxima

Community Member Credit: Eddy I wanted to add a sequential shift light to my 2002 Nissan Maxima. After doing some research, I decided to go with the Ecliptech Shift-P2 Shift Light Light. Pretty simple and straightforward to install. I ordered it from the link below and these guys shipped it…

carsnwomen91’s Gen2 VQ35DE HR Swap How-to YouTube Video’s

Relevance: 42%      Posted on: 06/23/2020

carsnwomen91's Gen2 VQ35DE HR Swap How-to YouTube Video's

Credit: Rene aka https://www.youtube.com/user/carsnwomen91 Please subscribe to show them support! Part 1 - Introduction https://www.youtube.com/watch?v=LIBEMiUmcYk Part 2 - Inspecting and Opening the Motor https://www.youtube.com/watch?v=UCl_nSafhVk Part 3 - Timing Chain Assembly https://www.youtube.com/watch?v=xoljm21mltQ Part 4 - Cam Trigger Wheels https://www.youtube.com/watch?v=oEnqAsZ9HHM Part 5 - Trans Swap, First Start-Up https://www.youtube.com/watch?v=4kGXUOLpJBg

How to Change Bulb Light in the Dome Light to LED

Relevance: 40%      Posted on: 01/01/2018

How to Change Bulb Light in the Dome Light to LED

Member Credit: wariow3 Difficulty: Easy to moderate. Knowledge of LED's + Resistors Experience with soldering recommended Items needed: Small flat head screw driver small phillips screwdriver 5mm leds ,I used white LED's( around 10, more just incase they blow or just dont' work) I get mine off ebay from the…

How to Find & Remove Your ECU v1

Relevance: 40%      Posted on: 01/05/2017

How to Find & Remove Your ECU v1

Member Credit: Technosquareinc The pictures are from a 350z but you can see its just about the same exact procedure for a 6thgen. Tools required for ECU removal and re-installing.   1. 10 mm socket and ratchet (or equivalent) 2. Philip (cross) screw driver 3. Flat head screw driver Before…

Nissan Maxima P1706 Neutral Position Switch

Relevance: 40%      Posted on: 06/22/2019

Nissan Maxima P1706 Neutral Position Switch

Member Credit: EddyMaxx Adding some helpful information regarding this code P1706. The sensor was broken and I almost couldn't find it. Replacing the sensor resolved the code. I ran into this issue and decided to document my findings for anyone needing to troubleshoot this. P1706 Nissan DTC: Park Neutral Position…

How to Remove your Headliner on 6thgen Maxima

Relevance: 40%      Posted on: 01/20/2018

How to Remove your Headliner on 6thgen Maxima

Member Credit: BLKMAGIC You can start this project from any part you wish, so you do not have to follow the order I did things. I started in the front, and worked my way to the rear of the car for the most part, although you do have to jump…

How to Remove Rear Package Deck on 2004-2008 Maxima

Relevance: 39%      Posted on: 11/24/2018

How to Remove Rear Package Deck on 2004-2008 Maxima

Member Credit: Hawk7886 The stock speakers on the 04 Max just don't cut it for me, so I decided to take apart the rear deck and swap them out with a pair of 6X9s I had sitting around. I'm planning something with more punch in the future, but I figured…

How to Clean Throttle Body and Idle Air Control Valve (IACV) on 4thgen Maxima

Relevance: 37%      Posted on: 09/22/2019

How to Clean Throttle Body and Idle Air Control Valve (IACV) on 4thgen Maxima

Member Credit: Cdg2125 Tools Required: Ratchet 10m socket 12mm socket Flathead or 8mm socket Pliers or vise grips 1 can of Throttle Body cleaner 1 can of Carb cleaner (I find Berrymans B12 to work fastest) New throttle body gasket New IAC Valve Gasket (dealer only) Step 1: Disconnect battery.…

VQ37VHR Timing Chain Marks

Relevance: 37%      Posted on: 12/26/2020

VQ37VHR Timing Chain Marks

Community Member Credit: BULL Hello everyone, I put this together to help others out when doing timing in these engines. As great as this engine is, internally it has some life-threatening issues that will decrease it longevity if not addressed. These are in the timing chain area: Gallery gasket, Chain…

How to Install S/VAFC-II on 1995-99 4thgen Nissan Maxima

Relevance: 36%      Posted on: 10/19/2020

How to Install S/VAFC-II on 1995-99 4thgen Nissan Maxima

Community Member Credit: gtrrider / VQPower Brief Details: What can the device be used for: In the VTEC AFC II, the VTEC changeover point of a vehicle with a VTEC engine (in our case 00VI/MEVI) can be adjusted at an optional engine RPM. This fuel adjustment controller can increase and decrease…

How to Install Y-Pipe & Catalytic Convert on 5thgen Maxima

Relevance: 36%      Posted on: 01/14/2018

How to Install Y-Pipe & Catalytic Convert on 5thgen Maxima

Member Credit:  beancooker 1. Remove all heat shields (10mm wrench). 2. Remove O2 sensors. 3.Spray penetrating oil on all bolts to be taken out. YOU WILL NEED A PIVOTING ADAPTER FOR YOUR SOCKET WRENCH. Remove 3 bolts on front bank, 3 bolts on rear bank and 2 bolts on cat.…

How to Reset Your Check Engine Light Manually (CEL)

Relevance: 36%      Posted on: 01/08/2017

How to Reset Your Check Engine Light Manually (CEL)

This article explains the various ways of resetting and/or clearing codes on your 6thgens. It should also work for any of the current generation Nissan and Infiniti vehicles. Clearing the codes will turn off any check engine lights (aka: SEL, CEL, SES, etc..). There is a table of OBDII codes…

Daily Driving My 5thgen Nissan Maxima on 100% E85 Fuel (1+Year Review)

Relevance: 35%      Posted on: 01/31/2021

Daily Driving My 5thgen Nissan Maxima on 100% E85 Fuel (1+Year Review)

Community Member Credit: Eddy Just wanted to share my experience and review with E85 over the past 1+ year on daily driving on E85 through all seasons. Not a lot of feedback out there on using E85 for daily driving or in general for the Nissan Maxima. Prior to doing…

How to Change your 7thgen CVT Transmission Fluid (Drain/Refill)

Relevance: 33%      Posted on: 12/29/2017

How to Change your 7thgen CVT Transmission Fluid (Drain/Refill)

Member Credit: Ghozt I just did my CVT transmission fluid drain/fill the other day, I'm at ~44,000 miles and premium maintenance service plan recommended every 40,000 while standard recommended every 60,000. With how I drive I figured it's about time so why not. I got my fluid on fleabay, picked…

How to Install Home Depot Front Bumper Lip Mod on 6thgen

Relevance: 33%      Posted on: 01/20/2018

How to Install Home Depot Front Bumper Lip Mod on 6thgen

Member Credit: AANTONE Alot of people dont think very high of doing this mod but if your not one of them and your interested enjoy! What you need: ( all can be purchased at you local Lowe's or Home Depot ) 1. A razor blade or scissors 2. 3M red double…

How to Install a 2000 5thgen VI Manifold on 4thgen Nissan Maxima

Relevance: 33%      Posted on: 02/16/2020

How to Install a 2000 5thgen VI Manifold on 4thgen Nissan Maxima

Member Credit: sdot82 This write-up is for a 2000-01 VI manifold swap on to 95-99 Maxima. There are many ways to do this swap so first I will number the ways I know how to do this and then go into detail on how to do it. There are a…