Search results for "Air lift"
| Results 1 - 30 of 68 | Page 1 of 3 |
| Sorted by: Relevance | Sort by: Date | Results per-page: 10 | 20 | 50 | All |
Member Credit: Cheston WARNING: These are JUST directions. I am NOT liable if you mess up your car. Use common sense when attempting this or ANY mod. Always use caution when it comes tools that use electricity. WEAR PROTECTIVE CLOTHING! Tools needed: phillips & flat head screwdriver, 10mm socket, 12mm socket,…
Member Credit: Sparky This 2003 Nissan Maxima came in with the complaint that the passenger front window would go down on it’s own. What I determined was that when the window was raised up, it would automatically cycle down about six inches. If the glass, motor or regulator have been…
Member Credit: Scrambler My SES light came on the other day and the code is indicating O2 sensor Bank 1, Sensor 1. That is the bank that is on the back side of the engine, against the firewall. Sensor 1 is the sensor in the exhaust manifold before the cat. BTW...…
Member Credit: Greg Changing the spark plugs on a 2002-2003 Maxima is not something you should have to do until around 100,000 miles. The stock plugs are platinum tipped and should last a very long time. Replacement of the plugs is something that Nissan recommends you "see your dealer" to…
Member Credit: chrisaust First, this is fairly easy once you figure it out the first time. Here are my step-by-step tips to get access to the gauges. ****IMPORTANT NOTE BEFORE YOU BEGIN**** If you plan to remove the needles, you'll need to remember how to put them back on so they…
Member Credit: EddyMaxx (Additional photos/info by chrisaust and CleanMaxx) Are you looking to get rid of that orange cluster on your 2004-2006 Nissan Maxima? Well you can install an 07-08 cluster very easily as everything is plug-n-play. All you need to do is purchase a cluster with miles closest to…
Owner: Felix Lespérance Year: 2003 Model: Maxima Current Color: Silver Transmission: Automatic to 6-Speed Manual HLSD Conversion Trim: GLE Dyno - 283 WHP / 243 TQ Due to low engine compression, the car did not make its expected horsepower.Once resolved, this car will make 340WHP+. Mod List: Engine Gen2 VQ35DE 2010 ACL Racing…
Member Credit: TEQ-NIQ Step 1: Remove shifter knob - Shifter knob is made of two parts, the leather handle, and the lower aluminum-looking cone-shaped piece. Grasp the cone-shaped lower piece, rotate counter-clockwise and pull down at the same time to release from shifter handle. Once this is done, there is a…
Community Member Credit: Rochester Part: Shifter Stabilizer Bushings - Nissan Maxima - 7.1115 Order Link: https://www.energysuspensionparts.com/7.1115 Here are the notes on removing the shifter trim and center console. Pictures follow. Remove the ashtray and the screw behind the ashtray. (picture) Unsnap the shifter trim by gently pushing your fingers into…
Member Credit: Greg I ordered the Injen Cold-Air Intake from Adventon.Com for the price of $238.56, which included UPS 3-day shipping. If you don't need it in 3 days, knock $13.75 off that price. I found Adventon a pleasure to deal with and would highly recommend them to anyone interested…
Credit: redlinegoods To install on an automatic, you need to wedge the shift boot between the shifter assembly and the trim piece surrounding it. Therefore it is necessary to remove that surrounding trim. When removing the trim piece surrounding the shifter, hazard switch and power outlet, the thing to be…
Community Member Credit: ATTappman Recently I had to remove my UIM to tighten the hose clamps on the coolant hoses connected to the backside of the UIM. Here's a description of the job with some photos. The car is a 1997 GLE Fed spec. Part 1: First, you have to…
These headers are no longer in production. They were available between 2004-2007 and are very rare to find these days. The information below is only for reference purposes. Part#: NS3017 System Components: Includes 2 headers and one secondary with flex-pipe. System also includes 2 center copper gaskets,cat.gasket, all necessary hardware and…
Article: EddyMaxx Over the past few months, our FX35 started to experience some odd behavior. When scanning the car for codes it would throw U1001 - Invalid or Missing Data for Primary Id. I noticed this happened about a week after a major rain day that ended up clogging and…
Raul has been an active member in Maxima community for many years. He currently owns and operates Tune On the Go. With over 10 years of experience and honest work, Raul will make sure your vehicle gets the work it needs while you rest at ease in the hands of a…
Member Credit: VQpwrdSE-R So I finally buckled down and added info in here for how to change your oil sending unit also known as an oil pressure sensor. Hoping this helps some of you guys out. The beginning of my problems was when I noted 0 psi on my oil pressure…
Credit: redlinegoods 1. In order to remove the front section, you must first remove the shift knob (just unscrew it from the shifter shaft - if it's difficult, use vice grips on it after wrapping it with a towel to protect it from scratches). Then remove the liner of the shifter.…
Member Credit: pmohr This howto is for the quick and easy task of removing the gauge cluster. Replacing bulbs, tightening up the tach or speedo screws, tapping into an easily accessible tach signal, swapping clusters, whatever. Most seem to remove the steering column trim when doing this. It does make it a…
Credit: redlinegoods 1. Start by removing your Shift Console. 2. Pull the the rear of the shift console towards you and slightly lift. 3. Pull the console slowly until it separates from the lower portion of the radio. 4. Turn the shift knob counter clockwise to remove it. You will…
Credit: DennisMik I would like to start by thanking JNCoRacer for his motivational pep talk. He was smart enough to know that I could do it, even though I didn't think I could. Thanks man. You will need various standard tools: screwdrivers (Phillips for screws & flat for prying), wire…
Community Member Credit: Trini Boom As some of you may know, when you go over bumps or rough road surfaces, you hear a clunking noise that sounds like metal to metal contact in your steering wheel. This thread will show you how to fix the problem. Tools Needed: Ratchet with…
Community Member Credit: Kevin Kryzda Tools necessary: 10mm socket and an extension Flathead screwdriver (or pry tool) Wire/Side Cutters or Wire Strippers Wire taps or soldering tools Before You Start: The purpose of this modification is to re-wire your fog light relay under your hood to receive signal from an…
Member Credit: Wildman04 I did the rear door first and the rear doors are a lot easier than the front doors are to do. The rear doors will take around 45 minutes to an hour and the front doors about two hours each, so probably allow a good day for…
Member Credit: cfr94 This installation process is for a set of Eibach Suspension Springs Pro Kit 6369.140 with 2.0" drop in front & 0.8" drop in rear. REAR END: 20-30 minutes Tools Needed: Air rachet or air gun, 18mm socket 3/4" open wrench & adjustable floor jack These instructions are…
Member Credit: beancooker 1. Remove all heat shields (10mm wrench). 2. Remove O2 sensors. 3.Spray penetrating oil on all bolts to be taken out. YOU WILL NEED A PIVOTING ADAPTER FOR YOUR SOCKET WRENCH. Remove 3 bolts on front bank, 3 bolts on rear bank and 2 bolts on cat.…
Community Member Credit: fxlr8 MATERIALS: ORDER YOUR FILTER (MAKE SURE YOU GET THE ACTIVATED CARBON FILTER) Part Number: FC35530 Order Link: https://www.ebay.com/itm/FC35530-CAF1792-CABIN-AIR-FILTER-2002-06-ALTIMA-2004-08-MAXIMA-2003-07-MURANO/200923445579?hash=item2ec7f8794b:g:-4gAAOSw4ERZbld~ TOOLS: PHILLIPS SCREWDRIVER SAFETY EVEN IF THIS PROCEDURE DOES NOT REQUIRE RAISING OF THE VEHICLE, WE CANNOT STRESS ENOUGH...NEVER GET UNDER A RAISED VEHICLE WITHOUT THE USE OF…
Member Credit: evintho Fixed my non working climate control with a mode door motor replacement. Took some pics while I was at it to hopefully help the next guy who does it. The beast in question is my '99 GLE. First I ran diagnostics as per the FSM. Everything pointed…
Member Credit: Sparky This 2007 Nissan Maxima came in with the complaint that the gas gauge was stuck on empty. Actually a closer look revealed that the gauge needle was stuck under the empty stop peg. Due to the coloring of the instrument cluster lens I was unable to get…
Member Credit: Scrambler68 Note: Dealing with suspension components are very dangerous, please use cautious when handling a loaded spring as harm may occur. 1. Jack up the vehicle and support with jack stands. 2. Remove the front wheels and you will see this: 3. Remove the sway bar end link…
Owner: Voltaire Cacal Instagram: @dmvolt Year: 2010 Model: Maxima Color: Ocean Gray (RAP) Transmission: Automatic (CVT) Trim: SV Sport Voltaire Cacal says his 2010 Nissan Maxima is not only the perfect daily driver for him and his family of five, but it also possesses all the luxurious features he was looking for. The sports…
